Amewi RC Mercedes-Benz Arocs Kipper 6x6 red 1/18 RTR

Detailed product description

RC model of the Mercedes Arocs 6x6 dump truck for remote control suitable for beginners as well as advanced drivers. The model is made of metal and plastic.

Thanks to the increased ground clearance, robust 6WD drive via metal cardan shafts and full suspension, the model is capable of driving even in more demanding terrain. In addition, it has differentials on all axles and softer tires compared to other models, which ensure better traction on loose or sandy surfaces. It has a load capacity of up to 4 kilograms and includes an integrated sound module and LED lighting that can be turned on and off using the remote control.

The fully assembled model is delivered in a beautiful transport box made of high-strength foam material, which reliably protects the model, remote control and safe storage of all components.

WARNING: The manufacturer states the incorrect scale of 1/14 on the packaging!

Features:

• 6WD drive with metal cardan shafts for maximum off-road performance
• Pre-installed LED and sound module: Can be switched on and off via remote control
• Body made entirely of metal and with strong worm gear: For maximum lifting power for easy transport of even heavy loads up to 4 kilograms
• Officially licensed model
• Differentials on the front axle and both rear axles
• Light suspension with leaf springs on the front axle
• Illuminated beacons on the roof
• Operating time up to 25 minutes
• Proportional control

Technical data:

• Scale: 1/14
• Length: 445 mm
• Width: 150 mm
• Height: 210 mm
• Weight: 4197 g including battery
• Wheelbase: Axle 1-3 = 270 mm, Axle 1-2 = 183 mm
• Front track width: 130 mm
• Rear track width: 120 mm
• Ground clearance: 25 mm
• Wheels: outer diameter/width 65/28 mm
• Rim diameter: 35 mm
• Gearbox: metal
• Differentials: metal
• Brake: electronic
• ESC: DC All-in-One
• Motor: DC
• Drive system: Cardan
• Main material: Metal and plastic
• Battery compartment dimensions: 75x40x20mm
• Battery: Li-Ion 2S 7.4V 2500mAh 5C round XT30, 70x36x20mm, 98g
• Riding time: up to 25 min
• Maximum speed: approx. 10 km/h
• Remote control: 7 channels, 2.4 GHz
• Range: approx. 50-80m
• Charger: USB cable
• Charging time: approx. 120-150 min

Package contents: RC model MB Arocs, Drive battery, USB charging cable, Remote control, Instructions DE/EN

Need to purchase: 4x 1.5V AA batteries for the remote control

Run-in of the new electric motor
New model with engine, needs to be run in first. Before starting to use the DC electric motor, it is definitely recommended to run it. Some manufacturers require it as a condition for recognizing a possible engine claim. The purpose of the run-in is to seat the rotating parts well, smooth the friction surfaces of the contacts, and grind the carbons into the correct shape. The current enters the motor on the commutator surfaces using the so-called carbons, which may not have a perfectly adapted shape from production. If the new motor is loaded to the maximum without a previous run-in, the commutator surface or the carbons may be damaged due to large "sparking". The run-in will allow the carbons to settle on the commutator as perfectly as possible. Thus, the carbons will wear out less and last longer.

Electric motor run-in procedure:
-If you have a new RC model car or boat in which the engine is already mounted, proceed as follows. Place the model on the mat so that the wheels rotate above the surface. Let the engine run at the lowest possible speed for at least 20-30 minutes. You can then drive the model for 20-30 minutes at a lower speed and gradually increase the speed. Drive the model at full power only after the run-in phase has passed.

-If you have a new engine that has not yet been installed in the model, you can do the run-in in the traditional, proven way by immersing it in water. Connect the motor to the ESC controller and lower it by the cables vertically down into a container of clean water. Start the engine at low speed and let it run for 10-15 minutes. Then you can gradually increase the speed for a few minutes up to the maximum. finally, take the motor out of the water and let it run for a while to blow the water out of the motor. You can mount a run-in engine in the model and you can immediately drive at full power. You don't have to worry about the engine submerged in water. It will work normally and the water will cool it during the run-in. In addition, it washes out carbon particles during grinding (the water visibly darkens).

Protection against overheating of the electric motor:
Since the stator is made up of permanent magnets, it is good to know that these magnets gradually lose their "power". However, temperature also has a big impact. Each electric motor heats up during operation and can reach a temperature of 60°C (therefore, the motor must never be touched with bare hands after driving!). However, if the engine is not cooled or cooled insufficiently, or if it is driven for a long time at maximum speed, it may overheat and thus weaken the magnets. Even after cooling down, the engine will no longer reach its previous performance. Of course, other parts of the engine can also be damaged by high heat. It is therefore advisable to change the load mode, or to drive with two smaller accumulators with a break for replacement and cooling, rather than with one large-capacity one for a long time at full power.

Electric motor replacement, tuning:
If you decide to replace the electric motor in this model, pay attention to the following recommendations.
The new motor should be of the same type (size), have the same number of turns and the same supply voltage value as the original one. That way, you will be sure that the model will retain its original driving characteristics.
If you are planning a tuning motor, first of all, check whether the original ESC controller in the model will be able to work with the tuning motor, in order not to burn the ESC controller, or to prevent the ESC-motor system from working. When tuning a motor, it is usually necessary to replace a pinion with a different number of teeth.

WARNING! This RC car is not a toy, but a more sophisticated, functional model that behaves very much like a real car. Due to its realistic parameters, if it is not properly assembled and operated, it can cause you injury, or injure the viewer, or damage property. The model is intended for driving in a large room or outside on a dry surface. Driving in water, in snow, in puddles, mud, sand, in tall grass without appropriate waterproof treatment can cause damage to the electronics of the model. Driving on public roads and other places (e.g. parking lots) with car traffic is prohibited. Do not drive in thick grass, you will overheat or burn the engine!
This model requires regular maintenance, by disassembling it correctly according to the service manual, you will not lose the warranty.